New Mitchell Instrument MIT6501 5kV Insulation Resistance Tester

The MIT6501 is a quality low cost solution for 5kV insulation resistance testing, built into a rugged hard case it can handle the rugged outdoor environments with ease.  Featuring everything you would expect, the MIT6501 also has internal storage of up to 200 measurements and software to create, save and print reports.

• High Visibility, High Contrast Next Generation Organic LED (OLED) Display


• Test insulation resistance up to 10TΩ


• Four Insulation Test Voltage Output Ranges: 500V, 1000V, 2500V, 5000V DC


• DAR and PI automatic calculations


• Adjustable test duration: 1 to 30 minutes


• Safety Voltmeter - if any voltage is detected (AC or DC) the tester will automatically switch to voltage detection mode


• PC Connection - Optically isolated USB connection allows real time display on PC as well as saved measurement transfer


• Manually store up to 200 individual tests to internal on-board memory


• Overload protected


• Audible and Visual warning of external voltage presence (above 30V)

http://www.mitchellinstrument.com/mitchell-instrument-mit6501-5kv-insulation-resistance-tester-megohmmeter.html

Cordless Phasing Tester

 The PD800W Cordless Phasing Tester accurately and easily operates in multiple applications including phasing, voltage detection, phase sequencing and phase angle indication.  You will only need this one kit for three-phase secondary systems, capacitive test points, URD systems and overhead and transmission/substation systems. This unique tester operates like a conventional phasing tester, but does not require an interconnecting cable or extension resistors. Each kit contains a Reference Probe(Transmitter) and a Meter Probe (Receiver). Each probe is water resistant, has a strong construction designed to withstand wear and is completely shielded to minimize stray field interference.

Mitchell Instrument 213112 High Voltage Detector

Mitchell Instruments High Voltage Detector offers an eight position rotary switch selects high voltage ranges. As the High Voltage Detector is moved closer to the voltage carrying conductor, its sensor head detects the high voltage carrying conductor's radiated electric field.

Salisbury SKJP11-1200 12 Cal Arc Flash Protection Kit

Salisbury SKJP11-1200 12 Cal Arc Flash Protection Kit with Jacket and Over Pants. This Arc Flash Protection Kit also includes the AS1200HAT Arc Flash Protection Face Shield and Hard Hat.

Salisbury Pro Wear Arc Flash Protection Jacket & Overpants Kits are clothing kits containing an arc flash jacket with hood in an ATPV rating of 12 cal/cm2, an AS1200HAT, Arc Flash Apparel Bag and safety glasses.
Sizes S, M, L, XL, 2XL, and 3XL available from stock. Other sizes and orange color available by special order.

THESE KITS MEET NFPA 70E HAZARD RISK CATEGORY 2

Insulated Glove Testing

Item of the day 3-2-10

Rubber Insulating Testing Schedule

Glove Testing Form

Type of equipment

When to test

-----------------------------------------------------------------------
Rubber insulating blankets............... Before first issue and every 12 months thereafter.*
Rubber insulating gloves.................. Before first issue and every 6 months thereafter.*
Rubber insulating sleeves................. Before first issue and every 12 months thereafter.*
-----------------------------------------------------------------------
*If the insulating equipment has been electrically tested but not issued for service, it may not be placed into service unless it has been electrically tested within the previous 12 months.
Prices starting at $12.00 Per Glove Set, $25.00 Per Set of Sleeves and $30.00 Per Blanket.
Every item is individually tracked at the laboratory. Gloves and sleeves are individually ID-labeled.
Other tested items are given individual test numbers.
Individual tracking allows us to:
• Identify ownership of items tested,
• Provide detailed itemized test reports,
• Maintain reliable test records.
All items are identified with the test date, the test voltage, and the name of our laboratory.
All items returned to customers are cleaned, visually inspected, and electrically tested. Items failing test and inspection (rejects) are clearly marked and returned to customer, unless local disposal is authorized.

Per OSHA (29 CFR 1910.137) requires all testing procedures above.
Mitchell Instrument Co. Inc
1570 Cherokee St
San Marcos Ca 92078
1-888-270-2690

Salisbury AS1200HAT 12 cal/cm2 Arc Flash Protection Faceshield Unit $89.99

Item of the day 3-1-10

The AS1200HAT has an ATPV rating of 12cal/cm2 and utilizes nanotechnology to provide a clearer, more transparent window for improved visibility. The shield/window is designed to be easily replaced without
tools. The faceshield unit includes ventilation ribs that allow a natural convection air flow through the top of the face shield. This reduces fogging of the visor, lowers CO2 levels and improves comfort for the user.

Hioki 3197 Power Quality Analyzer Kit - 500 Amp

Item of the day 2-25-10

Hioki 3197 custom kit includes three 500 Amp AC current clamps and professional software

• QuickSet function sets power quality detection levels to industry standards
• Simultaneously Detect Transient Over-voltages, Voltage Swells,Voltage Dips, Interruptions, Inrush Current
• Capture Power Conditions at a Glance;Voltage,Current,Active / Reactive / Apparent Power, Power Factor, Displacement Power Factor, Active/Reactive Energy, Demand, Harmonics (voltage, current, power),THD, Unbalance,K Factor, Phase Angle
• Control and Download Data to your PC via a USB connection
• Frequently Measured Power Quality Conditions are Preset for Easy Access
• Up to 6 Hours of Continuous Use with the Rechargeble Battery

AC Voltage: up to 600 Volts AC
AC Current: up to 5000 Amps with optional Flex probe’s
AC Frequency: 50 to 60 Hz (auto detect)
Preset System Configurations: Single Phase 2 or 3 wire, Three Phase Delta or Wye 3 or 4 wire
Power Measurments: Voltage, Current, Active/Reactive/Apparant Power, Power Factor, Displacement Power Factor, Active/Reactive Energy, Demand, Unbalance, K Factor, Phase Angle
Anomalies Detected: Transient Overvoltages, Voltage Swells, Voltage Dips, Interuptions, Inrush Current
Harmonics: Voltage, Current & Power, THD
Interval Settings: Auto 1/5/10/15/30/60 Minutes
PC Interface: USB 2.0
Maximum Recordable Period: 125 days (4 MB internal Memory)
Power Requirements: 100 to 240 VAC, 50 or 60

You may also be interested in the following product(s)

AEMC 3945-B PowerPad Power Quality Analyzer Kit - 240 Amp $3,695.00

Fluke 435 Power Quality Analyzer Kit 3000 Amp Flex Probe List Price: $7,476.00 This price is too low to display

Product Includes	three 500 amp clamp on current probes (1.8” inside diameter), voltage leads with aligator clips, rechargable battery pack,AC adapter, USB connection cable, Professional PC software, and Carrying case
Specifications	AC Voltage: up to 600 Volts AC AC Current: up to 5000 Amps with optional Flex probe’s AC Frequency: 50 to 60 Hz (auto detect) Preset System Configurations: Single Phase 2 or 3 wire, Three Phase Delta or Wye 3 or 4 wire Power Measurments: Voltage, Current, Active/Reactive/Apparant Power, Power Factor, Displacement Power Factor, Active/Reactive Energy, Demand, Unbalance, K Factor, Phase Angle Anomalies Detected: Transient Overvoltages, Voltage Swells, Voltage Dips, Interuptions, Inrush Current Harmonics: Voltage, Current & Power, THD Interval Settings: Auto 1/5/10/15/30/60 Minutes PC Interface: USB 2.0 Maximum Recordable Period: 125 days (4 MB internal Memory) Power Requirements: 100 to 240 VAC, 50 or 60
size	5 x 9.7 x 2.5
Shipping Weight	15.0000
Power Supply	rechargable battery pack
Manufacturer	Hioki
MPN	3197-01/500 Pro
Manufacturer Warranty	1 Year
Mitchell Catalog Number	WBMIT3197LP, 9PMIT3197LP, 8PMIT3197LP, 7PMIT3197LP

Product Tags

Add Your Tags:

Use spaces to separate tags. Use single quotes (') for phrases.

Mitchell MIT6500 5KV Insulation Resistance Tester

 Item of the day 2-24-10

 

 The Mitchell MIT6500 5KV Insulation Resistance Tester is the best value in its class with advanced testing and logging features.

•  250V to 5,000V output in 25V steps
•  Automatically calculates Dielectric Absorption Ratio (DAR) and Polarization Index (PI)
•  Stepped voltage test with five programable steps for both voltage and duration of each step
•  Temperature measurement from
•  Data storage function (100 groups of 360 tests)
•  Safety rated to 1000V Cat III and 600V Cat IV
•  Measure line for voltage prior to test (AC or DC)
•  Integrated hard carrying case is field tough
•  Rechargeable battery pack
•  Back lit display
•  USB PC interface and Logging function allows testing documentation

6 Ft Body Rescue Hook

Item of the day 2-23-10

An invaluable tool for any workplace used to withdraw an injured worker out of a hazardous area. Confined spaces, in vaults, or just near electrical cabinets and switch gear are some of the places where the Salisbury Insulated Rescue Hook is a must. Featuring a foam filled, fiberglass reinforced handle for superior electrical insulation and a coated heat treated body hook with an 18" opening. This combination produces a tool of the highest quality, durability, and reliability, setting a new industry standard.

For emergency rescue of injured personnel... “No electrical safety area should be without one” • Non-conductive handles constructed of the finest woven fiberglass materials and tested per OSHA and ASTM F-711 • High strength steel hook dipped in 1/8” thick black vinyl • Tested @ 15kV/6" or 100kV/ft • Easy-to-locate red handle...treated to provide maximum electrical protection

Non Contact AC High Voltage Detector

Item of the day 2-22-10

High Voltage Detector, Non Contact AC High Voltage Detector Rotary selector switch with following settings: OFF | TEST | 240V | 6kV | 11kV | 22kV | 33kV | 132kV | 275kV

• Designed to detect presence of high voltage without direct physical contact
• An eight or ten position rotary switch selects detection range; as sensor is moved closer to energized conductor, sensor head picks up radiated electric field; once threshold is reached, buzzer sounds and bright red warning light flashes
• For indoor or outdoor use
• User can manually self-test on standard model; an automatic self-test beeps every two seconds on advanced model, reassuring operator of proper operation
• Wide range of detection...finds 80V to 275kV; just one instrument fits all applications
• Lightweight, minimizes sway at end of longer hot sticks
• Selected voltage is detected approximately 10" away from voltage source; greater detection distances can be obtained at lower voltage positions on switch
• Large bright red warning light (two leds)
• Loud piezo buzzer
• Rotary selector switch with following settings: OFF | TEST | 240V | 6kV | 11kV | 22kV | 33kV | 132kV | 275kV
• Battery compartment/handle holds (3) "C" batteries
• Universal spline on end for connection to any standard hotstick; Included adapter allows use with shotgun clamp-sticks

Mitchell Instrument ATA3499 Digital Hydrometer

Item of the day 2-19-09

Digital Hydrometer measures specific gravity and is designed for stationary battery testing. The range is optimized to measure the specific gravity of sulfuric lead-acid battery fluid. This digital hydrometer is the quickest and most efficient way to maintain and ensure optimally charged industrial storage battery banks. The digital hydrometer measures a range from 1.000 to 1.3000 specific gravity (s.g.).

Digital hydrometer allows a quick and easy determination of specific gravity of sulfuric acid in batteries
Specific gravity measurements best identify failing battery cells compared to voltage testing, which only shows the float charge
The digital hydrometer also displays either concentration of ethylene glycol (%), freezing temp of ethylene glycol    (°C), or temp of sample cell (°C)
For measuring concentration of antifreeze solution used for central heating system...as a part of equipment, solution control
Ideal for measuring the condition of antifreeze solution for vehicle radiators
Perfect for measuring specific gravity of battery fluid (dilute sulfuric acid) in utility, telecommunication and switch gear stationary battery testing
Specific Gravity: Accuracy of ±0.005 units-500% faster than conventional sightglass methods
Battery fluid samples pumped through the digital hydrometer sample hose and nozzle to sample chamber where measurements are taken. Gasket ensures a liquid-tight seal
Waterproof membrane keypad     • Automatically temperature compensated to 77°F
No need to wipe down sample prism     • Measurement with one touch of a switch

STORAGE BATTERY TESTING WITH A DIGITAL HYDROMETER

Checking a storage battery (lead-acid) for its condition of charge or discharge is most efficiently done with a digital hydrometer measuring the specific gravity of the electrolyte. A specific gravity reading between 1.275 and 1.300 indicates a full-charge condition. A reading of 1.250 indicates that the battery is half charged and a reading of 1.175 is indicative of full discharge. Since the acids (electrolyte) can differ from battery to battery, specific gravity readings may differ. But a good rule of thumb is to recharge batteries after a decrease in specific gravity reading of 0.100 from the reading at full-charge condition. The digital hydrometer is the fastest and most cost-effective solution for peak performance. Hydrometer readings should not vary more than .05 differences between cells.

Taken From: FACILITIES INSTRUCTIONS, STANDARDS, AND TECHNIQUES VOLUME 3-6; HYDROELECTRIC RESEARCH AND TECHNICAL SERVICES GROUP 1998

1.4 SPECIFIC GRAVITY READINGS (Most effectively taken with a digital hydrometer)
Specific gravity readings of vented lead-acid batteries must be taken in accordance with the following instructions. Note: All specific gravity readings must be corrected to 77EF before recording (see 2.18). Do not attempt to take any specific gravity reading after adding water to a cell. The electrolyte takes several hours to mix after water is added.
A. Monthly
Take the specific gravity reading of the pilot cell and record it on form POM133A.
B. Quarterly
Take specific gravity readings of 10 percent of the total number of cells and record them on form POM-133A. Rotate these cells so that readings are taken on different cells each quarter.
C. Annually
Take specific gravity readings of every cell and record them on form POM133A.
D. After Equalizing Charge
About 15 minutes after heavy gassing stops, take the specific gravity readings of every cell and record them on form POM-133A. If two cells with the lowest specific gravity (checked over the last one-eighth of the charging period) have not stopped rising, continue the equalizing charge.

Product Includes	Includes two suction tubes, hand strap, battery, case and certificate of conformity
Specifications	Sensor: optical refraction with thermal sensor Ranges: Ethylene glycol concentration: 0-70% (0.1 res) Ethylene glycol freeze pt: 0-50C (0.1 res) Specific gravity battery fluid: 1.000 to 1.300 Accuracy: ±0.1% conc., ±0.1C f.p., ±0.005s.g. Temperature of sample cell: 5-40°C / ±1°C Quantity of sample: Two ml or more Material: ABS resin body and sensor section as resin for sample cell
size	1.9 x 8.3 x 2.8”
Shipping Weight	4.0000
Power Supply	9V Battery
Manufacturer	Mitchell Instrument
MPN	ATA3499
Manufacturer Warranty	2 Year Parts & Labor
Mitchell Catalog Number	9LATA3499, 8LATA3499, 7LATA3499, WBATA3499

Product Tags

Other people marked this product with these tags:

• battery tester (1)
• digital hydrometer (1)

Add Your Tags:

Use spaces to separate tags. Use single quotes (') for phrases.

Mitchell MITCT917 Advanced Thermo-Hygrometer

 Item of the day 2-18-10

The Mitchell MITCT917 Advanced Thermo-Hygrometer can measure Temperature, Humidity, Dewpoint and wetbulb temperature.

•    Measure Temperature, Humidity, Dewpoint and Wet Bulb temperature
•    Bright backlit dual display
•    Built-in probe with pull up protecive cap
•    Data Hold and Max/Min values diplayed on demand
•    0.1% RH resolution and 0.1°F Temp. resolution
•    All readings selectable in °F or °C

A thermohygrometer is invaluable for facility maintenance and utility technicians, HVAC contractors, and specialists who assess indoor air quality (IAQ). Lightweight, rugged, and easy to hold, our meters are the perfect tool for monitoring problem areas.

FLIR I5 Low Cost Thermal Imaging Camera

Item of the day 2-17-10

The FLIR Systems I5 Low Cost Thermal Imaging Camera is Pocket Sized and Extremely Lightweight Camera weighs less than a pound

•    The first truely affordable infrared camera that fits in the palm of your hand

•    Removable MiniSD Memory Card can store up to 5000 radiometric JPEG images

•    So affordable every plant engineer, electrician and maintenance professional should have one!

•    Quick, focus free lens allows for quick inspections

•    High accuracy and thermal sensitivity helps pinpoint problems faster

•    Double molded rugged design with easy grip handle meets IP43 dust/splash standards

•    Fully automatic design make it incredibly easy-to-use even for first time users

Typical Applications
•    Find overloaded circuit breakers
•    Identify problems in motors
•    Check for overheating in transformers
•    Inspect fans & bearings
•    Detect hidden problems
•    See hotspots to avoid future electrical failures

Mitchell MIT6500 5KV Insulation Resistance Tester

 

Item of the day 2-16-10

•  250V to 5,000V output in 25V steps
•  Automatically calculates Dielectric Absorption Ratio (DAR) and Polarization Index (PI)
•  Stepped voltage test with five programable steps for both voltage and duration of each step
•  Temperature measurement from
•  Data storage function (100 groups of 360 tests)
•  Safety rated to 1000V Cat III and 600V Cat IV
•  Measure line for voltage prior to test (AC or DC)
•  Integrated hard carrying case is field tough
•  Rechargeable battery pack
•  Back lit display
•  USB PC interface and Logging function allows testing documentation

Cementex Insulated Tool Set 59 Pieces ITS60B $1,980.00

Item of the day 2-15-10

Cementex Insulated Tool Set 59 Pieces ITS60B        $1,980.00

• MRO Super Kit
• 9" Linesman's Plier P9SCNE
• 8" Needle Nose Plier P8CN
• 7-1/2" Diagonal Plier P7D
• 8" Slip Joint Plier P8SJ
• 10" Crimping Plier P100CT
• 10" Water Pump Plier P10WP
• 12" Water Pump Plier P12WP
• 6" Flat Nose Plier P6-DB
• 9-1/2" Cable Cutting Plier P9CC
• 9" Combination Stripper/Crimper WS19
• 9/64" x 2" Cabinet Tip Screwdriver, Cushion Grip M2
• 3/16" x 4" Cabinet Tip Screwdriver, Cushion Grip MC4P-CG
• 3/16" x 6" Cabinet Tip Screwdriver, Cushion Grip MC6P-CG
• 1/4" x 6" Cabinet Tip Screwdriver, Cushion Grip M6-CG
• 5/16" x 6" Mechanic's Tip Screwdriver, Cushion Grip Y6-CG
• #2 x 4" Phillips Tip Screwdriver, Cushion Grip P2-4-CG
• #2 x 8" Phillips Tip Screwdriver, Cushion Grip P2-8-CG
• 3/16" x 6" Extra Long Nutdriver, Cushion Grip ND100CGXL
• 1/4" x 6" Extra Long Nutdriver, Cushion Grip ND200CGXL
• 5/16" x 6" Extra Long Nutdriver, Cushion Grip ND300CGXL
• 11/32" x 6" Extra Long Nutdriver, Cushion Grip ND400CGXL
• 3/8" x 6" Extra Long Nutdriver, Cushion Grip ND500CGXL
• 7/16" x 6" Extra Long Nutdriver, Cushion Grip ND600CGXL
• 1/2" x 6" Extra Long Nutdriver, Cushion Grip ND700CGXL
• 3/16" T-Handle Hex Wrench IHK-316
• 1/4" T-Handle Hex Wrench IHK-140
• 5/16" T-Handle Hex Wrench IHK-516
• 3/8" T-Handle Hex Wrench IHK-380
• 7/16" T-Handle Hex Wrench IHK-716
• 1/2" T-Handle Hex Wrench IHK-120
• 3/8" Square Drive Lever Control Reversible Ratchet IR38-LC
• 3" Extension Bar: 3/8" Square Drive IB38-3
• 6" Extension Bar: 3/8" Square Drive IB38-6
• 1/16" Long Arm Hex Wrench IHW-116
• 1/8" Long Arm Hex Wrench IHW-180
• 3/16" Long Arm Hex Wrench IHW-316
• 1/4" Long Arm Hex Wrench IHW-140
• 5/16" Long Arm Hex Wrench IHW-516
• 3/8" Long Arm Hex Wrench IHW-380
• 7/16" Long Arm Hex Wrench IHW-716
• 1/2" Long Arm Hex Wrench IHW-120
• 5/16" Standard 12 Point Socket: 3/8" Square Drive IS38-10
• 3/8" Standard 12 Point Socket: 3/8" Square Drive IS38-12
• 7/16" Standard 12 Point Socket: 3/8" Square Drive IS38-14
• 1/2" Standard 12 Point Socket: 3/8" Square Drive IS38-16
• 9/16" Standard 12 Point Socket: 3/8" Square Drive IS38-18
• 5/8" Standard 12 Point Socket: 3/8" Square Drive IS38-20
• 11/16" Standard 12 Point Socket: 3/8" Square Drive IS38-22
• 3/4" Standard 12 Point Socket: 3/8" Square Drive IS38-24
• 13/16" Standard 12 Point Socket: 3/8" Square Drive IS38-26
• 7/8" Standard 12 Point Socket: 3/8" Square Drive IS38-28
• 3/8" Box End Wrench BEW-12
• 7/16" Box End Wrench BEW-14
• 1/2" Box End Wrench BEW-16
• 9/16" Box End Wrench BEW-18
• 5/8" Box End Wrench BEW-20
• 11/16" Box End Wrench BEW-22
• 3/4" Box End Wrench BEW-24
• 13/16" Box End Wrench BEW-26
• 7/8" Box End Wrench BEW-28
• 15/16" Box End Wrench BEW-30
• 1" Box End Wrench BEW-32

Fluke 28ii Waterproof Industrial Multimeter

Item of the day 2-12-10

• The NEW Fluke 28 II digital multimeters define a new standard for operating in harsh conditions with the features and accuracy to troubleshoot most electrical problems. Featureing IP 67 (waterproof and dustproof) rating, MSHA approvals (pending), extended operating temperature range of -15 °C to +55 °C (5 °F to 131 °F, -40 °C for up to 20 minutes) and 95 % humidity, and have been designed and tested to withstand a 3 m (10 ft) drop. The new Fluke 28 II Multimeter is built to work in the toughest environments.Measure up to 1000 V ac and dc
• Measure up to 10 A (20 A for 30 seconds)
• 10,000 μF capacitance range
• Frequency to 200 kHz
• Extended ac voltage bandwidth– 15 Hz to 20 kHz
• Built in thermometer conveniently allows you to take temperature readings without having to carry a separate instrument
• Resistance, continuity and diode test
• Min/Max and average recording to capture variations automatically
• Peak min-max
• Unique function for accurate voltage and frequency measurements on adjustable speed motor drives and other electrically noisy equipment
• New – IP 67 waterproof & dustproof protection, completely sealed for use in harsh environments
• Designed to withstand 3 meter drop (with holster)
• Hi resolution 20,000 count display mode
• True-rms ac voltage and current for accurate measurements on non linear signals
• New – Backlit keypad buttons allow for easy visibility in lowlit areas
• Large display digits and 2 level bright white backlight for increased visibility
• Reversible holster for added protection when not in use
• Withstands hazardous 8,000 volt spikes caused by load switching and faults on industrial circuits and complies with second edition IEC and ANSI electrical safety standards
• Long battery life (800 hours)
• Relative mode to remove test lead resistance from low ohms measurements
• Auto and manual ranging for maximum flexibility
• MSHA approval (pending)

Cable Length Meter

Item of the Day 2-11-10

The MIT710 Digital Cable Length Meter is an excellent tool to measure spooled cable/wire. This best seller has been upgraded with improved resolution and accuracy for reading lengths greater than 300 ft, and is able to store information for common wire types and offer six user programmable positions for custom wires. Ideal for major utility companies, electrical contractors, wholesalers, and installers where quick and accurate inventory management or measurements are needed for job accountability. Simply attach the Kelvin Clips to both ends of the cable and adjust the indicator to the size wire being measured. A temperature compensation circuit ensures accuracy by compensating for the temperature of the wire.

Features
• New – Improved resolution to .001Ω, 0.5 ft.
• New – Improved accuracy to ±1% of reading for lengths
   greater than 300 ft (100m)
• New – 6 user programmable custom wire settings
• Measures copper and aluminum cables; covers the major
   wire gauges
• Automatic temperature compensation
• Reads in feet and meters
• Milliohm measurement capability
• Wire size: 26 ga – 4/0 ga
• 250 MCM – 500 MCM
• Resistance 99.9Ω
• Auto off
• Two easy-to-attach Kelvin Clip leads connect to cable
• 22 pre-set wire gauge settings
• Five year limited warranty